BTS-P600 Polyurethane Road Marking Paint
Product Introduction:
Baotashan BrandBTS-P600 Polyurethane Road Marking Paintis a two-component coating formulated by blendinghydroxyl resin, weather-resistant pigments, wear-resistant fillers, additives, curing agents, etc. %% into a composite mixture.A two-component paint formulated by mixing.
Product Performance:
CoatingThe film is dustproof, waterproof, wear-resistant, with strong coloring power and excellent weather resistance.
Recommended Uses:
ApplicableFor indoor and outdoor asphalt, concrete, colored anti-slip pavement markings, and multi-component resin floor paint markings.
Technical Guide：
project | Component | Component |
Usage Time | 4.0hours(10℃） | 3.0hours(23℃） | 2.0hours(30℃） |
Curing time | Surface Dry45min（10℃） | 30min（23℃） | 25min（30℃） |
Hard work12hours(10℃） | 10hours(23℃） | 8hours(30℃） |
Specific gravity | 1.2-1.4 | 1.0 |
Color | Various colored viscous liquids | Colorless transparent liquid |
Mixing ratio | Component/BComponent组份=100:25 |
|
Solid Content | 60%Above (after mixing) |
|
Construction Instructions：
Mixing—— Proportionately mixPour component A and component B into the mixing bucket and stir thoroughly until well blended, then add the matching thinner to achieve the desired application viscosity.
Construction Method—— Roller coating, spray coating
Recommended dosage—— 1kg can mark 25-30 meters of 15cm wide solid lines on resin flooring
Construction Conditions—— SubstrateMoisture Content RequirementsBelow 8%, with relative air humidity under 80%. Avoid application during rainy days, when relative humidity exceeds 80%, or when temperatures fall below 5°C.℃The mixing ratio should follow the instructions on the packaging. Prepare the solution as needed, mix only the required amount, and stir thoroughly. Use it within the specified time frame to avoid gel waste.
Mixing ratio—— Follow the ratio indicated on the packaging. Prepare the mixture as needed, mix only the required amount, and ensure thorough stirring. Use it within the specified time frame to prevent gel waste.
Dilution ratio—— 10-15%Special thinner
Tool cleaning—— Special thinner
Recommended matching system:
Asphalt %% /Cement substrate+ %% Our company's various two-component resin floor paints %% +BTS-P600 Polyurethane marking paint/cement base material +BTS-P600 Polyurethane Road Marking Paint
Our company's various two-component resin floor paints+BTS-P600 Polyurethane Marking Paint
storage：
It must be stored in accordance with national regulations. The storage environment should be dry, cool, well-ventilated, and away from heat sources and open flames. The packaging containers must remain tightly sealed.
storage：
AtIt can be stored for at least 12 months at a temperature of 25°C. Store in the original sealed container, keeping the storage area cool and dry. Prevent the packaging container from freezing. Storage temperature must not be lower than5℃。
Loading and unloading:
Handle with care. Stir well before use.
Package size:
Component (Base Material)Kilograms：20Component (Curing Agent)Kilograms (Curative) 5 kg
Health and Safety:
Please note the warning labels on the packaging containers. Use under well-ventilated conditions. Avoid swallowing or inhaling paint mist. Prevent skin contact; if paint splashes onto the skin, immediately wash with appropriate cleanser, soap, and water. In case of eye contact, rinse thoroughly with clean water. %%。
Declaration：
The information provided in this product manual is entirely based on the knowledge we have gained in the laboratory and through practice. However, since the use of the product is generally beyond our control, we only guarantee the quality of the product itself. We reserve the right to modify this manual without prior notice.
English
Pусский
简体中文
